How to Choose a Custom Inflatable Finish Line Arch for Your Race

How to Choose a Custom Inflatable Finish Line Arch for Your Race?
Quick Answer
Measure the gap your race needs before choosing an inflatable finish line arch. Check the clear width at the height you need, then put the arch feet, timing mats, barriers and guy lines on the same site plan. Before signing off on the artwork, mark where the finish-line photographer will stand. That tells you which face should carry the main sponsor logo.
What Size and Shape of Inflatable Finish Line Arch Will Fit?
If a supplier quotes an 8 m inflatable arch, ask them to show where that measurement starts and ends. On an angled or round arch, there may be plenty of room between the legs at ground level while the shoulders narrow the opening higher up.
The quickest check is to draw the passage you need as a rectangle on the front elevation. Look at the two upper corners. If either corner crosses the inside edge of the arch, that profile cuts into the space your race needs.
| MX arch shape | Listed width options | What to look for |
| Angled | 4, 5, 6, 8, 10 and 12 m | Check how far the sloping shoulders extend into the opening at the required height. |
| Round | 4, 5, 6, 7, 8, 9, 10 and 12 m | Measure the clearance at both edges of the passage. The center is the highest point. |
| Straight | 4, 5, 6, 8, 10 and 12 m | Start here if you need a wide opening near the top. Check the gap between the legs and the height beneath the beam. |
| Semi | 2.1 and 2.3 m | Check where the quoted width is measured on the drawing and how much of it is usable. |
These are the listed series widths. The drawing for your chosen configuration gives you the dimensions to compare with your course. MX inflatable arch size options
Say your race needs 6 m of clear width up to 2.5 m high. On a hypothetical angled arch drawing, the opening measures 6.4 m at ground level and 5.8 m at 2.5 m. That puts it 20 cm short where you need the clearance. Before going up a size, compare the opening of a straight arch that fits the same site.
Will the Feet and Guy Lines Fit Around the Timing Mats?
An arch leg can sit outside the athlete lane and still end up in the timing crew’s working space. A guy line can clear the mats and cross a staff access route. The front elevation won’t show either conflict. You’ll see them when you put the feet, ballast and lines on the finish-area plan.
Start with the timing point agreed for your race. Place the arch directly above the mats if the feet and fixings leave enough room for the equipment, crew and athlete passage. If shifting the arch solves a conflict, have the timing team and race organizer review the new position before you approve the drawing. Running USA finish-area planning guide
How Do You Set Up and Secure an Inflatable Race Arch?
How Long Does Setup Take?
Two people can set up an inflatable finish line arch in about 5–10 minutes. Allow additional time for anchoring and final checks before opening the finish area.
Have the pump ready when the crew arrives. An MX sealed-air inflatable arch needs power for initial inflation. Once inflated and sealed, it stays up during normal use without a continuously running blower.
How Do You Secure the Arch on Asphalt or Concrete?
We typically secure sandbags or other ballast to the arch legs and run guy lines from the upper attachment points to suitable anchors. On the site plan, draw each line all the way to its anchor. That gives the crew a chance to spot a line crossing a staff route or a ballast bag taking up space beside the timing mats.
How much ballast do you need, and what wind limit applies? Confirm both for the arch size and fixing layout you intend to use. Send MX the surface type, the anchor points the venue allows and the marked site plan. Before race day, establish how much ballast goes at each fixing point, what operating wind limit applies to that arrangement and when the crew needs to take the arch out of use.
What Should You Approve Before Ordering a Custom Inflatable Arch?
Can You Hang a Race Clock from the Arch?
MX can sew attachment points below the top banner, but a clock mount needs load testing for the specific arch size and configuration. Customers have used this position to hang display banners. MX has yet to test it with a race clock and has no standard load rating for that use.
If you want to hang a clock, send its dimensions, the combined weight of the clock and mounting hardware, and how you plan to attach it. Put a separate clock stand on the initial site plan so the timing team has a layout it can review while the proposed mount is assessed.
Where Should the Primary Sponsor Logo Go?
For a head-on finish photo that includes the arch top, center the main sponsor logo on the upper panel facing the camera. If the photographer stands beyond the finish and shoots back toward incoming athletes, that’s the face looking into the post-finish area.
For a side shot that crops out the top, test the leg panel the camera can see. Check the planned frame with a barrier and an athlete in view to see whether either blocks the lettering. If the photographer is shooting tight portraits that exclude the arch entirely, use a separate sponsor backdrop if the logo needs to appear in those shots.
Mark the camera position and expected crop on the artwork proof. On a round arch, check the full logo where it sits on the curved print area. Running USA finish-area photography guidance
Can You Change the Sponsor Graphics Between Races?
Yes. MX can sew hook-and-loop fasteners at selected positions on the front and back of the arch, including the top and leg display areas. You can swap the removable panels between races. Graphics printed directly onto the outer cover stay on that cover.
For a race series, print the event branding on the cover and use removable panels for the sponsors that change. On the front and rear proofs, mark exactly which areas will use panels. That’s also the time to check that the sponsor panel lands in the photographer’s frame.
What Does the Venue Need to Review?
Send the venue the same arch drawing and site plan your timing team is using. Ask which supporting documents it needs, then have MX confirm which installation instructions and material documents apply to the proposed configuration.
If the venue asks you to move the arch, check the timing layout and camera-facing artwork again before signing off. A move that clears an access route can also change which face the photographer sees.
Should You Rent or Buy an Inflatable Finish Line Arch?
Rent for a one-off race if a stock arch fits the course and gives your sponsors the space they need. Buy a custom inflatable finish line arch if the course needs a specific opening, the artwork needs to fit a particular camera angle, or you’ll use the same arch across a race series. For several events, add up the rental, delivery, setup and collection fees for every date. Compare that total with purchase, transport, storage and any replacement sponsor panels.
MX EXPERIENCE sells made-to-order inflatable arches. We configure the shape, dimensions and graphics for each event.
When Should You Order?
Use your test setup date as the delivery deadline. Tell MX where the arch is going and the latest date it can arrive. For European destinations, we can quote air or sea freight and confirm whether duties-paid delivery (DDP) is available for your address.
Can You Replace the Bladder or Printed Cover?
Yes. You can buy and replace the TPU air bladder and printed outer cover separately. If the arch loses air, send MX a short video so we can help identify the problem and advise on the replacement. If the cover is damaged or the graphics printed on it need updating, you can order a new cover and keep the existing bladder.
What Should You Send for a Custom Inflatable Arch Quote?
Start with a marked finish-area plan. Show the clear width and height you need, the space available for the feet and fixings, and the positions of the mats, barriers and clock. Add the ground surface, permitted anchor points, artwork for each face, which graphics need to be removable, and your delivery address and deadline.
Ask for the dimensioned drawing with the quote. Your timing crew can check the opening and equipment positions, your sponsor can review the artwork, and your venue can assess the proposed fixing layout before you place the order. MX custom inflatable arch configurations
